Delptronics Thunderclap Manual de usuario descargar pdf

Thunderclap Kit Instructions V2 Page 1 of 11

Version

These instructions are for Version 2 of the Thunderclap PCB (printed circuit board). You can tell which version of the

PCB you have by looking in the lower right hand corner of the PCB. If you need the Version 1 instructions, you can

download them here: http://delptronics.com/documents/ThunderclapKitInstructions.pdf

Version 1 Version 2

Important Information

Thank you for your purchase of the Delptronics Thunderclap Kit!

Before you start, please read the Electronic Kit Soldering Tutorial. It contains important and useful information even

for experienced kit builders. If this is your first electronic kit, the best piece of advice we can give is to take your time

and be careful to put the right part in the right place. The tutorial can be downloaded here:

http://delptronics.com/documents/SolderingTutorial.pdf

In the instructions that follow, each part type is followed by the PCB outline for that part. Refer to the enclosed

photograph of the completed kit for assistance with part identification and placement.

The PCB is marked with the refdes (reference designator) of each part, not its value. For example R1 refers to

resistor number one and C1 refers to capacitor number one. Once the part value is identified, it is easy to find the

refdes on the PCB.

Some parts must be oriented in a particular way, that is, the correct lead goes in the appropriate hole in the PCB. For

example, electrolytic capacitors are polarized (they have a positive lead and a negative lead). Ceramic capacitors

are not polarized, so it does not matter which of the two leads goes in which of the two holes. In these instructions,

the symbol (±) highlights parts that must be inserted with a particular orientation.

When you are ready to begin, separate the parts by type. Then, when you are ready to solder parts of a particular

type, separate them by value. Compare your parts to the bill of materials, which can be found on the last page of this

document. Make sure no parts are missing. These instructions list the parts in the recommended order of assembly.

In general, the order is shortest to tallest.

This manual is separated into two sections: board-mounted parts, which are soldered directly to the PCB, and off-

board parts which are connected to the PCB via wires.

1 2 3 4 5 6 ... 10 11

Bill of Materials 11

Indice de contenidos

Pagina 1

Thunderclap Kit Instructions V2 Page 1 of 11 Version These instructions are for Version 2 of the Thunderclap PCB (printed circuit board). You can

Pagina 2

Thunderclap Kit Instructions V2 Page 10 of 11 Finished That’s it. Your Thunderclap is complete. Congratulations! Pictures This is what the assem

Pagina 3

Thunderclap Kit Instructions V2 Page 11 of 11 Bill of Materials Board-mounted parts: Quantity Description Marking on part Refdes 1 BAT85 Schottky

Pagina 4

Thunderclap Kit Instructions V2 Page 2 of 11 Board-mounted Parts All of the board-mounted parts are supplied in a little plastic bag to keep them t

Pagina 5

Thunderclap Kit Instructions V2 Page 3 of 11 Schottky Diode (±) There are 8 diodes, but D1 is different. D1 is a Schottky diode and has “BAT85”

Pagina 6

Thunderclap Kit Instructions V2 Page 4 of 11 Chip Sockets (±) There are two 8-pin sockets and one 16-pin socket. Sockets are marked with a sma

Pagina 7

Thunderclap Kit Instructions V2 Page 5 of 11 Chips (±) There are three chips. Two of the chips are the same size, so refer to the photo to make su

Pagina 8

Thunderclap Kit Instructions V2 Page 6 of 11 Off-board Parts These parts are connected to the PCB via wires, as opposed to being soldered directly

Pagina 9

Thunderclap Kit Instructions V2 Page 7 of 11 Potentiometers The potentiometers (pots) can either be soldered directly to the PCB, or they can be

Pagina 10

Thunderclap Kit Instructions V2 Page 8 of 11 Output Jack (±) Your kit came with either ¼ inch or 3.5 mm jacks like the ones shown below. Refer t

Pagina 11 - Bill of Materials

Thunderclap Kit Instructions V2 Page 9 of 11 Stompbox Power (±) If your Thunderclap is a stomp box, the simplest way to connect the power is to

Comentarios a estos manuales

Sin comentarios

Delptronics Thunderclap Manual de usuario

Busca en linea o descarga Manual de usuario para Instrumentos musicales Delptronics Thunderclap. Delptronics Thunderclap User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales